Instant Download API: API-580 Free Updated Test Dumps
Valid API-580 FREE EXAM DUMPS QUESTIONS & ANSWERS
Who should take the API-580 exam
The API Risk Based Inspection API-580 Exam certification is an internationally-recognized validation that identifies persons who earn it as possessing skilled as Risk Based Inspection Certification. If a candidate wants significant improvement in career growth needs enhanced knowledge, skills, and talents. The API Risk Based Inspection API-580 Exam certification provides proof of this advanced knowledge and skill. If a candidate has knowledge of associated technologies and skills that are required to pass API Risk Based Inspection API-580 Exam then he should take this exam.
What is the duration of the API-580 Exam
- Format: Multiple choices, multiple answers
- Number of Questions: 70
- Length of Examination: 3.25 hours
NEW QUESTION # 15
_________________curves are referred for the deterioration mechanism for carbon and low ally steel
materials.
- A. Schmidt curves for sulfide corrosion
- B. PH concentration curves
- C. Nelson curves
Answer: C
NEW QUESTION # 16
The type of failure mode that likely to occur due to mechanical and metallurgical deterioration
- A. Small holes to ruptures
- B. Cracks
- C. Leaks
- D. Catastrophic ruptures
Answer: D
NEW QUESTION # 17
In general, the probability of failure is determined by
- A. Consequence detailed
- B. A&B
- C. Effectiveness of inspection program
- D. Deterioration mechanism
Answer: D
NEW QUESTION # 18
The primary work products of the rbi assessment and management approach and implementation of rbi provides
- A. Overall increase of risk and acceptance of risk
- B. Overall reduction of risk and negligence of current risk
- C. Overall increase of risk and negligence of current risk
- D. Overall reduction of risk and acceptance of current risk
Answer: D
NEW QUESTION # 19
Qualitative assessment is done on the basis of
- A. Knowledge of operating History
- B. All the above
- C. Inspection plans
- D. Possible material deteriorations
Answer: A
NEW QUESTION # 20
When equipment has low deterioration rates as an inspector what you decide in lieu of internal inspection.
- A. External inspection
- B. On-stream inspection
- C. Out of service inspection
Answer: B
NEW QUESTION # 21
Failure mode can primarily affects the
- A. Consequences
- B. Magnitude
- C. A&B
Answer: B
NEW QUESTION # 22
Deterioration for specific process equipmentis not available, this can be sourced from
- A. Experience with other similar equipment
- B. All the above
- C. Previous inspection data
- D. Published data
Answer: D
NEW QUESTION # 23
Consequence is always __________ for safety aspects
- A. Negative
- B. Neutral
- C. Positive
Answer: A
NEW QUESTION # 24
A process to assess risks, to determine if risk reduction is required and to develop a plan to maintain risks at an acceptable level
- A. Risk mitigation
- B. Risk management
- C. Risk control
Answer: B
NEW QUESTION # 25
A physical condition or a release of a hazardous material that could result from component failure and result in human injury or death, loss or damage, or environ- mental degradation
- A. Loss
- B. Hazard
- C. Failure
Answer: B
NEW QUESTION # 26
____________uses logic models depicting combinations of events
- A. Process hazard analysis
- B. Qualitative risk analysis
- C. Quantitative risk analysis
Answer: C
NEW QUESTION # 27
Hazard identification in a rbi analysis generally focuses on identifiable failure mechanisms in the equipment (inspectable causes) but does not explicitly deal with
- A. Other potential failure resulting from events such as flammable fire due to leak from equipment
- B. Other potential failure scenarios resulting from events such as power S failures or human errors
- C. Environmental impact caused due to toxic release
Answer: B
NEW QUESTION # 28
Termination of the ability of a system, structure, or component to perform its required function of containment
of fluid (le loss of containment)
- A. Risk
- B. Outcome
- C. Failure
Answer: C
NEW QUESTION # 29
Thinning causes the loss of material from
- A. Internal surfaces only
- B. External or internal surfaces
- C. External surfaces only
Answer: C
NEW QUESTION # 30
______________to be established to judge acceptability of risk couldhe an objective of the rbi assessment if such criteria do not exist already within the user's company.
- A. Risk analysis
- B. Risk plan
- C. Risk criteria
Answer: C
NEW QUESTION # 31
Following will cover the functional failures except
- A. Rotating equipment failure ^
- B. Pressure relief device failure
- C. Static equipment failure due to process environment
- D. Heat exchanger tube failure
Answer: A
NEW QUESTION # 32
Aqueous chloride solution is carried into a sensitized stainless steel vessel, the following cracking mechanism takes very rapidly depending on temperature.
- A. Sulphide stress corrosion cracking
- B. Chloride stress corrosion cracking
- C. Leak can occur
Answer: B
NEW QUESTION # 33
The type of failure mode that likely to occur due to pitting
- A. Small holes to ruptures
- B. Cracks
- C. Catastrophic rupture
- D. Small hole sized leaks
Answer: D
NEW QUESTION # 34
Probability side of the risk equation is normally managed by
- A. Maintenance planning engineers
- B. Process safety personnel
- C. A&B
- D. Plant inspectors or inspection engineers
Answer: D
NEW QUESTION # 35
Following are the critical variables for deterioration mechanism except
- A. Material of construction
- B. Insulation
- C. Process operating
- D. Start up and shut down conditions
Answer: B
NEW QUESTION # 36
____________ uses logic models depicting combinations of events
- A. Process hazard analysis
- B. Qualitative risk analysis
- C. Quantitative risk analysis
Answer: C
NEW QUESTION # 37
......
Free API-580 Exam Braindumps API Pratice Exam: https://examsites.premiumvcedump.com/API/valid-API-580-premium-vce-exam-dumps.html